@MastersThesis{Contin:2014:DeDiCV,
author = "Contin, Andr{\'e}",
title = "Deposi{\c{c}}{\~a}o de diamante CVD sobre a{\c{c}}o 304 com
interface de sic obtida por laser cladding",
school = "Instituto Nacional de Pesquisas Espaciais (INPE)",
year = "2014",
address = "S{\~a}o Jos{\'e} dos Campos",
month = "2014-02-26",
keywords = "filme de diamante CVD, laser cladding, A{\c{c}}o inox 304, HFCVD,
barreira intermedi{\'a}ria, CVD diamond film, laser cladding. 3.
304 stainless steel, HFCVD, intermediate barrier.",
abstract = "O emprego de filmes de diamante CVD em substratos de a{\c{c}}o
{\'e} uma aplica{\c{c}}{\~a}o de grande interesse devido
{\`a}s suas propriedades {\'{\i}}mpares. O uso do diamante CVD
como filme protetor, gera um aumento da dureza superficial, da
condutividade t{\'e}rmica e na redu{\c{c}}{\~a}o do atrito, e
consequentemente, melhor prote{\c{c}}{\~a}o {\`a}
corros{\~a}o. Apesar das dificuldades ainda encontradas em termos
de ader{\^e}ncia entre filmes de diamante e substratos de
a{\c{c}}o, a baixa raz{\~a}o custo-benef{\'{\i}}cio do
recobrimento com diamante sint{\'e}tico {\'e} vantajosa e,
portanto, almejada. O objetivo deste trabalho foi o de depositar
filmes de diamante CVD aderentes em substratos de a{\c{c}}o inox
304, utilizando uma nova t{\'e}cnica de forma{\c{c}}{\~a}o de
barreira intermedi{\'a}ria, realizada pelo processo de laser
cladding. Nesta t{\'e}cnica, uma fina camada de p{\'o} {\'e}
irradiada e fundida por um feixe de laser com o prop{\'o}sito de
fundir a camada de p{\'o} e a camada superficial do substrato
para criar o recobrimento. O controle dos par{\^a}metros do feixe
do laser permite a cria{\c{c}}{\~a}o de camadas homog{\^e}neas
de recobrimento, em {\'a}reas relativamente grandes, em poucos
segundos. Neste trabalho, utilizou-se o p{\'o} de carbeto de
sil{\'{\i}}cio (SiC) para criar a camada intermedi{\'a}ria.
Antes do crescimento de diamante, as amostras foram submetidas ao
processo de semeadura com p{\'o} de diamante. A
deposi{\c{c}}{\~a}o dos filmes de diamante foi realizada em um
reator HFCVD (Hot Filament Chemical Vapor Deposition) com
diferentes concentra{\c{c}}{\~o}es de gases para filmes
microcristalinos e nanocristalinos. Como parte dos resultados
obtidos, o teste de indenta{\c{c}}{\~a}o Rockwell mostrou a
melhoria da ades{\~a}o dos filmes de diamante nos substratos. A
microscopia eletr{\^o}nica de varredura (MEV) revelou a
morfologia dos filmes de diamante. Por difra{\c{c}}{\~a}o de
raios-X foi identificada as fases cristalinas da camada de SiC. O
n{\'{\i}}vel de tens{\~a}o residual dos filmes de diamante e o
de ader{\^e}ncia da camada de SiC foram avaliados pela
espectroscopia Raman e ensaio de microscratch, respectivamente.
ABSTRACT: The use of CVD diamond films on steel substrates is an
application of great interest due to their unique properties. The
use of CVD diamond film as a protective film generates an increase
in surface hardness, thermal conductivity and reduced friction
and, consequently, better corrosion protection. Despite the
difficulties still encountered in terms of adhesion between
diamond films and steel substrates, low cost-benefit ratio of the
coating with synthetic diamond is advantageous and, therefore,
desired. The objective of this work was to deposit CVD diamond
films adherents in 304 stainless steel substrates using a new
technique of forming intermediate barrier, made by laser cladding
process. In this technique, a thin layer of powder is irradiated
and melted by a laser beam in order to melt the powder layer and
the surface layer of the substrate to create the coating. The
parameters control of the laser beam allows the creation of
homogeneous layers of coating, in relatively large areas in
seconds. In this work, we used the powdered silicon carbide (SiC)
to create an intermediate layer. Before the diamond growth, the
samples were subjected to the process of seeding with diamond
dust. The deposition of diamond films was carried out in a reactor
HFCVD (Hot Filament Chemical Vapor Deposition) with different
concentrations of gases for microcrystalline and nanocrystalline
films. As part of the results obtained, the Rockwell indentation
test showed the improvement of adhesion of diamond films on
substrates. The scanning electron microscopy (SEM) revealed the
morphology of the diamond films. The X-ray diffraction identified
the crystalline phases of the SiC layer. The level of residual
stress of the diamond films and the adhesion of the SiC layer were
evaluated by Raman spectroscopy and microscratch test,
respectively.",
committee = "Corat, Evaldo Jos{\'e} (presidente/orientador) and Vasconcelos,
Get{\'u}lio de (orientador) and Gavinier, Divani Barbosa and
Bonetti, Luis Francisco",
englishtitle = "CVD diamond deposition on steel 304 with sic interface by laser
cladding",
language = "pt",
pages = "96",
ibi = "8JMKD3MGP7W/3FNE9DS",
url = "http://urlib.net/rep/8JMKD3MGP7W/3FNE9DS",
targetfile = "publicacao.pdf",
urlaccessdate = "28 jan. 2021"
}